内嵌式智能触控显示
- MP128FL电源液晶电源板26寸32寸55寸通用型麦格米特MP118FL电源板
- 类别：操控主板
- 特点：
品牌：麦格米特（MEGMEET）
型号：MP118FL
输出：24V=4A，12V=2A，5V=2.5A，5VSB=1A
适用范围：32-55寸LED液晶屏
尺寸（长*宽*高）：180MM*180MM*10MM
质保：一年保修
订购热线：13631625316
产品说明
1.2.3 Output Transient Response. （输出动态响应）
Table 4. Test condition.测试条件
Voltage
Tolerance Limit Slew Rate Load Change
5.0V/5.0VS±5%
24V/12V/±10%
0.2A/uS Min. to 50% load and 50% to Max load
All output±10% 0.2A/uS Min. load to Max load
Note: Transient response measurements shall be made with a load changing repetition
rate of 50Hz to 10kHz. 以50~10KHz 的频率跳变负载来测试。
1.2.4 Table 5 DC Output Hold-Up Time. （输出保持时间）
Output Voltage 120Vac input 220Vac input
+V1(+24V) ≥10 mS ≥10 mS
+V2(+12V) ≥10 mS ≥10 mS
+5.0V ≥10mS ≥10 mS
+5.0V(STB) ≥10 mS ≥10 mS
Note: All of dc output at full load. 所有输出带满载
1.2.5 Table 6 DC Output Overshoot At Turn On & Turn Off.（输出超调）
Output Channel Output(V) Over shoot voltage(V)超调电压
Turn on 开机 Turn off 关机
+V1(+24V) + 24V 10% 10%
+V2(+12V) + 12V 10% 10%
+5.0V +5.0V 10% 10%
+5.0V(SB) +5.0V 10% 10%
Note: All of dc output current from Min. to Max. 测试时负载范围：最小到最大
1.2.6 Table 7 DC output voltage rise time（输出上升时间）
Output Voltage 120Vac input &Full Load 220Vac input &Full Load
+V1(+24V) ≤100mS ≤100mS
+V2(+12V) ≤100 mS ≤100 mS
+5.0V ≤100 mS ≤100mS
+5.0V(SB) ≤50 mS ≤50 mS
Note: The output voltages shall rise from10% to 90% of their output voltage.
输出从10%上升到90%的时间
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
6 OF 11
1.3 Remote On/Off Control：（遥控功能）
The power supply DC outputs (without +5.0Vsb) shall be enable with an active-high
TTL(≥2.5V/2.0mA)-compatible signal(Ps-on). The +5.0Vsb is on whenever the AC
power is present.
除5.0Vsb 外，其余输出受控于一个TTL 电平兼容的信号（Ps-on≥2.5V/2.0mA）,
5.0Vsb 上电就存在。
* When Ps-on is pulled to TTL high, the DC outputs are to be enabled.
Ps-on 高电平，打开输出
* When Ps-on is pulled to TTL low or open circuit, the DC outputs are to be disabled.
Ps-on 低电平，关闭输出
Table 8.
Ps-on Signal Comments Outputs
Ps-on- high ≥2.5V&2.0mA ( source) Output
Ps-on- low ≤ 0.5V X
Ps-on-open -- X
1.4 Protection: （保护功能）
1.4.1 Table 9 DC output Over Voltage Protection. （输出过压保护）
Output Voltage TYP. Over Voltage Comments
+V1(+24V) 27V Power supply latch into shutdown state
输出锁机
+V2(+12V) 14V
Power supply latch into shutdown state
输出锁机
Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load.
应该在最大交流输入电压264 伏和轻载、空载下测试。
1.4.2 Table 10 DC Output Over current Protection. （输出过流保护）
Note:* The over current protection should be test at other of dc output at Rated load but the
24V over current protection should be test at 12Vdc output at min load.
5V 和5VSTB 过流保护测试是在其它额定负载时测试.而24V 过流测试是在12V 轻载电流时测试。
Output Voltage Over Current Comments
+V1(+24V) ≥6Atyp* Hiccup尝试重复启动
+V2(+12V) ≥5Atyp* Hiccup 尝试重复启动
+5V ≥2Atyp* Hiccup尝试重复启动
+5.0VSB ≥1.5Atyp* Hiccup 尝试重复启动
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
7 OF 11
1.4.3 Table 11 DC Output Short Circuit Protection. （输出短路保护）
Output Voltage Comments
+V1(+24V) Shutdown关机
+V2(+12V) Shutdown 关机*
+5V Hiccup 尝试重复启动
+5.0V(SB) Hiccup 尝试重复启动
Note:* The Short Circuit protection should be test at other of dc output at Rated load
短路保护测试是在其它额定负载时测试.
1.4.4 Reset After Shutdown.（保护功能复位）
Recycle the ps-on signal, the power supply will restart after the fault removed，But +5V、
+5.0V(STB)output over voltage can’t be reset.
故障去除后，关掉Ps-on 信号再打开，电源即可恢复。+5V、+5.0V(STB)过压后不可恢复。
2. Isolation（绝缘性能）
2.1 Table 12 （绝缘阻抗）
Input To Output DC500V 50MΩmin (at room temperature)
Input To FG DC500V 50MΩmin (at room temperature)
Output To FG Non Isolated
2.2 Table 13 （绝缘耐压）
Input To Output 3000Vac 50Hz 1minute ≤10mA
Input To FG 1500Vac 50Hz 1minute ≤10mA
Output To FG Non Isolated
Note: Open FG and Output return. 交流地和输出负极要断开。
3. Safety （安全规格）
The power supply shall compliance with the following Criterion:
电源安全性满足下列标准
1) UL60065
2) EN60065
3) GB8898-2001
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
8 OF 11
4. EMC （电磁兼容性）
4.1 EMI （电磁干扰）
The power supply shall compliance with the following Criterion:
电源电磁干扰满足下列规则：
1) Conduction Emission : （传导干扰度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
2) Radiated Emission : （辐射干扰度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
4.2 EMS （电磁抗扰）
The power supply shall compliance with the following Criterion:
电源电磁抗扰满足下列规则：
1) ESD （静电抗扰度）
*GB17626.2-1998/IEC61000-4-2
2) EFT （脉冲群抗扰度）
*GB17626.4-1998/IEC61000-4-4 3KV
3) Surge （雷击浪涌）
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV
5. Environmental Requirement （工作环境）
5.1 Temperature （环境温度）
* Operating: 0℃ to +40℃.
* Store: -20℃ to +80℃.
5.2 Humidity （环境湿度）
* Operating: From 10%to90% relative humidity (non-condensing).
* Store: From 5 to 95% relative humidity (non-condensing).
5.3 Altitude （海拔高度）
* Operating: to10,000 ft.
* Store: to 20,000ft.
5.4 Cooling Method （冷却方式）
* Ventilation cooling . 自然冷却
5.5 Vibration （振动耐受）
* 10-55Hz, 19.6m/s2(2G), 3minutes period, 60minutes each along X, Y and Z axis.
5.6 Impact （冲击耐受）
* 49m/s2(5G),11ms, once each X, Y and Z axis.
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
9 OF 11
6. Dimension （物理尺寸）
* 180mm × 180mm ×11mm (长L *宽W * 高H ).板面高
7. Weight （重量）
* 约500g
8. Pin Connection (连接器脚位定义)
Table 15 Pin-CON4 Connection And Function
NO. Pin Connection Function
5.6.7.8 GND +24VDC RETURN
1.2.3.4 +24V +24VDC OUTPUT
Note: CON4 -- XH CONNEETION, TYPE : pitch2.5mm
Table 16 Pin-CON3 Connection And Function
NO. Pin Connection Function
3.4 GND +24VDC RETURN
1.2 Vaudio +24VDC OUTPUT
Note: CON3 -- XH CONNEETION, TYPE : pitch2.5mm
Table 17 Pin-CON2 Connection And Function
NO. Pin Connection Function
1. 2 GND +5V +5VSB +12VDC RETURN
3.4 +5V +5VDC OUTPUT
5 STB SMPS ON/OFF CONTROL(ON = HIGH)
6 +5VSB STANDBY(+5.0VDC) OUTPUT
7.8 +5V +5VDC OUTPUT
9.10.11 GND +5V +5VSB +12VDC RETURN
12.13 +12V +12VDC OUTPUT
Note: CON2 -- XH CONNEETION, TYPE : pitch2.5mm
Table 18 Pin-CON5 Connection And Function
NO. Pin Connection Function
1.2.3 SGND +12VDC RETURN
4.5 +12V +12VDC OUTPUT
Note: CON5 -- XH CONNEETION, TYPE : pitch2.5mm
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
Table 4. Test condition.测试条件
Voltage
Tolerance Limit Slew Rate Load Change5.0V/5.0VS±5%
24V/12V/±10%
0.2A/uS Min. to 50% load and 50% to Max load
All output±10% 0.2A/uS Min. load to Max load
Note: Transient response measurements shall be made with a load changing repetition
rate of 50Hz to 10kHz. 以50~10KHz 的频率跳变负载来测试。
1.2.4 Table 5 DC Output Hold-Up Time. （输出保持时间）
Output Voltage 120Vac input 220Vac input
+V1(+24V) ≥10 mS ≥10 mS
+V2(+12V) ≥10 mS ≥10 mS
+5.0V ≥10mS ≥10 mS
+5.0V(STB) ≥10 mS ≥10 mS
Note: All of dc output at full load. 所有输出带满载
1.2.5 Table 6 DC Output Overshoot At Turn On & Turn Off.（输出超调）
Output Channel Output(V) Over shoot voltage(V)超调电压
Turn on 开机 Turn off 关机
+V1(+24V) + 24V 10% 10%
+V2(+12V) + 12V 10% 10%
+5.0V +5.0V 10% 10%
+5.0V(SB) +5.0V 10% 10%
Note: All of dc output current from Min. to Max. 测试时负载范围：最小到最大
1.2.6 Table 7 DC output voltage rise time（输出上升时间）
Output Voltage 120Vac input &Full Load 220Vac input &Full Load
+V1(+24V) ≤100mS ≤100mS
+V2(+12V) ≤100 mS ≤100 mS
+5.0V ≤100 mS ≤100mS
+5.0V(SB) ≤50 mS ≤50 mS
Note: The output voltages shall rise from10% to 90% of their output voltage.
输出从10%上升到90%的时间
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
6 OF 11
1.3 Remote On/Off Control：（遥控功能）
The power supply DC outputs (without +5.0Vsb) shall be enable with an active-high
TTL(≥2.5V/2.0mA)-compatible signal(Ps-on). The +5.0Vsb is on whenever the AC
power is present.
除5.0Vsb 外，其余输出受控于一个TTL 电平兼容的信号（Ps-on≥2.5V/2.0mA）,
5.0Vsb 上电就存在。
* When Ps-on is pulled to TTL high, the DC outputs are to be enabled.
Ps-on 高电平，打开输出
* When Ps-on is pulled to TTL low or open circuit, the DC outputs are to be disabled.
Ps-on 低电平，关闭输出
Table 8.
Ps-on Signal Comments Outputs
Ps-on- high ≥2.5V&2.0mA ( source) Output
Ps-on- low ≤ 0.5V X
Ps-on-open -- X
1.4 Protection: （保护功能）
1.4.1 Table 9 DC output Over Voltage Protection. （输出过压保护）
Output Voltage TYP. Over Voltage Comments
+V1(+24V) 27V Power supply latch into shutdown state
输出锁机
+V2(+12V) 14V
Power supply latch into shutdown state
输出锁机
Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load.
应该在最大交流输入电压264 伏和轻载、空载下测试。
1.4.2 Table 10 DC Output Over current Protection. （输出过流保护）
Note:* The over current protection should be test at other of dc output at Rated load but the
24V over current protection should be test at 12Vdc output at min load.
5V 和5VSTB 过流保护测试是在其它额定负载时测试.而24V 过流测试是在12V 轻载电流时测试。
Output Voltage Over Current Comments
+V1(+24V) ≥6Atyp* Hiccup尝试重复启动
+V2(+12V) ≥5Atyp* Hiccup 尝试重复启动
+5V ≥2Atyp* Hiccup尝试重复启动
+5.0VSB ≥1.5Atyp* Hiccup 尝试重复启动
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
7 OF 11
1.4.3 Table 11 DC Output Short Circuit Protection. （输出短路保护）
Output Voltage Comments
+V1(+24V) Shutdown关机
+V2(+12V) Shutdown 关机*
+5V Hiccup 尝试重复启动
+5.0V(SB) Hiccup 尝试重复启动
Note:* The Short Circuit protection should be test at other of dc output at Rated load
短路保护测试是在其它额定负载时测试.
1.4.4 Reset After Shutdown.（保护功能复位）
Recycle the ps-on signal, the power supply will restart after the fault removed，But +5V、
+5.0V(STB)output over voltage can’t be reset.
故障去除后，关掉Ps-on 信号再打开，电源即可恢复。+5V、+5.0V(STB)过压后不可恢复。
2. Isolation（绝缘性能）
2.1 Table 12 （绝缘阻抗）
Input To Output DC500V 50MΩmin (at room temperature)
Input To FG DC500V 50MΩmin (at room temperature)
Output To FG Non Isolated
2.2 Table 13 （绝缘耐压）
Input To Output 3000Vac 50Hz 1minute ≤10mA
Input To FG 1500Vac 50Hz 1minute ≤10mA
Output To FG Non Isolated
Note: Open FG and Output return. 交流地和输出负极要断开。
3. Safety （安全规格）
The power supply shall compliance with the following Criterion:
电源安全性满足下列标准
1) UL60065
2) EN60065
3) GB8898-2001
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
8 OF 11
4. EMC （电磁兼容性）
4.1 EMI （电磁干扰）
The power supply shall compliance with the following Criterion:
电源电磁干扰满足下列规则：
1) Conduction Emission : （传导干扰度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
2) Radiated Emission : （辐射干扰度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
4.2 EMS （电磁抗扰）
The power supply shall compliance with the following Criterion:
电源电磁抗扰满足下列规则：
1) ESD （静电抗扰度）
*GB17626.2-1998/IEC61000-4-2
2) EFT （脉冲群抗扰度）
*GB17626.4-1998/IEC61000-4-4 3KV
3) Surge （雷击浪涌）
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV
5. Environmental Requirement （工作环境）
5.1 Temperature （环境温度）
* Operating: 0℃ to +40℃.
* Store: -20℃ to +80℃.
5.2 Humidity （环境湿度）
* Operating: From 10%to90% relative humidity (non-condensing).
* Store: From 5 to 95% relative humidity (non-condensing).
5.3 Altitude （海拔高度）
* Operating: to10,000 ft.
* Store: to 20,000ft.
5.4 Cooling Method （冷却方式）
* Ventilation cooling . 自然冷却
5.5 Vibration （振动耐受）
* 10-55Hz, 19.6m/s2(2G), 3minutes period, 60minutes each along X, Y and Z axis.
5.6 Impact （冲击耐受）
* 49m/s2(5G),11ms, once each X, Y and Z axis.
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
(规格书)
SPECIFICATION
THESE SPECIFICATION ARE THE PROPERTY OF MEGMEET ELECTRICAL TECHNOLOGY CO., LTD
AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL
OF APPARATUSES OR DEVICES WITHOUT PERMISSION.
Model No.:
MP118TH-C
DATE PREPARED CHECKED APPROVED Document No.:
REV:
2010/06/22 ZHAN XING GUICHENCAI ZHANGZHI 1.0
9 OF 11
6. Dimension （物理尺寸）
* 180mm × 180mm ×11mm (长L *宽W * 高H ).板面高
7. Weight （重量）
* 约500g
8. Pin Connection (连接器脚位定义)
Table 15 Pin-CON4 Connection And Function
NO. Pin Connection Function
5.6.7.8 GND +24VDC RETURN
1.2.3.4 +24V +24VDC OUTPUT
Note: CON4 -- XH CONNEETION, TYPE : pitch2.5mm
Table 16 Pin-CON3 Connection And Function
NO. Pin Connection Function
3.4 GND +24VDC RETURN
1.2 Vaudio +24VDC OUTPUT
Note: CON3 -- XH CONNEETION, TYPE : pitch2.5mm
Table 17 Pin-CON2 Connection And Function
NO. Pin Connection Function
1. 2 GND +5V +5VSB +12VDC RETURN
3.4 +5V +5VDC OUTPUT
5 STB SMPS ON/OFF CONTROL(ON = HIGH)
6 +5VSB STANDBY(+5.0VDC) OUTPUT
7.8 +5V +5VDC OUTPUT
9.10.11 GND +5V +5VSB +12VDC RETURN
12.13 +12V +12VDC OUTPUT
Note: CON2 -- XH CONNEETION, TYPE : pitch2.5mm
Table 18 Pin-CON5 Connection And Function
NO. Pin Connection Function
1.2.3 SGND +12VDC RETURN
4.5 +12V +12VDC OUTPUT
Note: CON5 -- XH CONNEETION, TYPE : pitch2.5mm
MEGMEET 麦格米特电气技术有限公司
MEGMEET ELECTRICAL TECHNOLOGY CO., LTD.
DESCRIPTION:
- 上一个：工控一体机教学机带液晶电源板麦格米特MP118TX-145功率145W
- 下一个：没有了
